EcoRouter Documentation

Command summary EcoRouter Documentation / Command summary

A brief description of the commands shown in the table below.

The table contains a description of the command, the console mode in which this command is available, the roles for which the command is available.
The following denotations are used in the "Mode" column:

User - user mode of console,

Admin - administration mode of console,

Conf - configuration mode of console.

Commands that are only available for the admin role and are not allowed for any other roles are marked with the letter d (access denied).

Command	Description	Mode	Role
			admin	noc	helpdesk
bgp	Border Gateway Protocol (BGP)	User	+
clear	Reset functions	User	+
crypto	Security specific commands	User	+
debug	Debugging functions (see also 'undebug')	User	+
disable	Turn off privileged mode command	User	+	+	+
enable	Turn on privileged mode command	User	+	+	+
exit	End current mode and down to previous mode	User	+	+	+
help	Description of the interactive help system	User	+	+	+
logout	Exit from the EXEC	User	+	+	+
no	Negate a command or set its defaults	User	+	+	+
ping	Send echo messages	User	+
quit	Exit current mode and down to previous mode	User	+	+
show access-group	Show access group	User	+	+
show access-list	Show access list configuration	User	+	+
show banner motd	Show current motd banner message	User	+	+
show bgp	Border Gateway Protocol (BGP)	User	+	+
show bridge	Bridge status and configuration	User	+	+
show bridge mac-table	Bridge mac-table	User	+	+
show cli	Show CLI tree of current mode	User	+	+
show clns	Connectionless-Mode Network Service (CLNS)	User	+	+
show controller	Controller status and configuration	User	+	+
show counters	Counters	User	+	+
show debugging	Debugging information outputs	User	+	+
show dhcp-profile	DHCP profile configuration	User	+	+
show filter-map	Filterring rules	User	+	+
show flow-export-profile	Flow export profile configuration	User	+	+
show hostname	Hostname	User	+	+
show hw	Ecorouter platform
show interface	Interface configuration	User	+	+
show ip	Internet Protocol (IP)	User	+	+
show isis	Intermediate System - Intermediate System (IS-IS)	User	+	+
show lacp	LACP	User	+	+
show ldp	Label Distribution Protocol (LDP)	User	+	+
show list	Show command lists	User	+	+
show users localdb	Display users database information	User	+	d	d
show log	Display log	User	+	+
show mirror-session	Mirror session status and configuration	User	+	+
show mpls	Show MPLS specific data	User	+	+
show platform	Show platform information	User	+	+
show port	Port status and configuration	User	+	+
show pppoe	Point-to-Point over Ethernet (PPPoE)	User	+	+
show privilege	Show current privilege level	User	+	+
show reports	Show existing reports	User	+	+
show role	Display information about role	User	+	d	d
show running-config	Current Operating configuration	User	+	+
security-profile	Security profile	User	+	+
show traffic-classifier	Traffic classifier status and configuration	User	+	+
show traffic-limiter	Traffic limiter status and configuration	User	+	+
show traffic-scheduler	Traffic scheduler status and configuration	User	+	+
show transceiver	Transceiver information	User	+	+
show uptime	Show system uptime	User	+	+
show users connected	Display information about terminal lines	User	+	+
show version	Display version	User	+	+
show virtual-router	Virtual Router information	User	+	+
show vrrp	VRRP information	User	+	+
terminal	Set terminal line parameters	User	+	+	+
undebug	Disable debugging functions (see also 'debug')	User	+	+	+
virtual-container	Virtual container settings	User	+
bgp	Border Gateway Protocol (BGP)	Admin	+
boot	Boot options of EcoRouterOS	Admin	+
clear	Reset functions	Admin	+
configure terminal	Enter configuration mode	Admin	+
copy	Copy from one place to another	Admin	+
copy report	Upload report to remote server	Admin	+
crypto ca export	Certification Authority settings	Admin	+
crypto certificate export	Display security information	Admin	+
crypto key export	User private key	Admin	+
debug	Debugging functions (see also 'undebug')	Admin	+
delete report	Delete existing reports	Admin	+
develop	Debug command	Admin	+
disable	Turn off privileged mode command	Admin	+
enable	Turn on privileged mode command	Admin	+
exit	End current mode and down to previous mode	Admin	+	+	+
faults	Fault management command	Admin	+
help	Description of the interactive help system	Admin	+	+	+
image	Image of EcoRouterOS	Admin	+
login	Login as a particular user	Admin	+	+	+
logout	Exit from the EXEC	Admin	+	+	+
mstat	show statistics after multiple multicast traceroutes	Admin	+	+	+
mtrace	Trace multicast path from source to destination	Admin	+	+	+
no	Negate a command or set its defaults	Admin	+
ping	Send echo messages	Admin	+	+	+
poweroff	Turn system off	Admin	+
quit	Exit current mode and down to previous mode	Admin	+	+	+
reload	Halt and perform a cold restart	Admin	+
reload in <1-600>	Shedulle device reboot (in minutes)	Admin	+
reload cancel	Cancel the shedulled reboot	Admin	+
restart	Restart process	Admin	+
show access-group	Access group	Admin	+	+
show access-list	Access list configuration	Admin	+	+
show arp	ARP table	Admin	+	+
show banner motd	Show current motd banner message	Admin	+	+
show bgp	Border Gateway Protocol (BGP)	Admin	+	+
show boot	Boot configuration of EcoRouterOS	Admin	+	+
show bridge	Bridge status and configuration	Admin	+	+
show bridge mac-table	Bridge mac-table	Admin	+	+
show cli	Show CLI tree of current mode	Admin	+	+
show clns	Connectionless-Mode Network Service (CLNS)	Admin	+	+
show controller	Controller status and configuration	Admin	+	+
show counters	Counters	Admin	+	+
show debugging	Debugging functions (see also 'undebug')	Admin	+	+
show develop	Debug output	Admin	+	+
show dhcp-profile	DHCP profile configuration	Admin	+	+
show faults	Show recorded faults	Admin	+	+
show filter-map	Filterring rules	Admin	+	+
show flow-export-profile	Flow export profile configuration	Admin	+	+
show hostname	Hostname	Admin	+	+
show hw	EcoRouter platform	Admin	+	+
show images	Images that can be used to upgrade EcoRouterOS	Admin	+	+
show interface	Interface configuration	Admin	+	+
show ip	Internet Protocol (IP)	Admin	+	+
show isis	Intermediate System - Intermediate System (IS-IS)	Admin	+	+
show lacp	LACP	Admin	+	+
show ldp	Label Distribution Protocol (LDP)	Admin	+	+
show list	Show command lists	Admin	+	+
show users localdb	Display users database information	Admin	+	+
show log	Display log	Admin	+	+
show mirror-session	Mirror session status and configuration	Admin	+	+
show mpls	Show MPLS specific data	Admin	+	+
show mrib	MRIB	Admin	+	+
show nsm	NSM	Admin	+	+
show ntp	Configuration NTP	Admin	+	+
show platform	Show platform information	Admin	+	+
show port	Port status and configuration	Admin	+	+
show pppoe	Point-to-Point over Ethernet (PPPoE)	Admin	+	+
show privilege	Show current privilege level	Admin	+	+
show process	Process	Admin	+	+
show process-group	Process	Admin	+	+
show proc-names	Show process names	Admin	+	+
show reports	Show existing reports	Admin	+	+
show rib	RIB	Admin	+	+
show role	Display information about role	Admin	+	+
show route-map	Route-map information	Admin	+	+
show router-id	Router ID	Admin	+	+
show routing	Display routing information	Admin	+	+
show running-config	Current Operating configuration	Admin	+	+
show security-profile	Security profile	Admin	+	+
show snmp	Display snmp settings	Admin	+	+
show startup-config	Contents of startup configuration	Admin	+	+
show tech-support	Show router technical information	Admin	+	+
show tech-support-vr	Show technical information of non privileged	Admin	+	+
show traffic-classifier	Traffic classifier status and configuration	Admin	+	+
show traffic-limiter	Traffic limiter status and configuration	Admin	+	+
show traffic-scheduler	Traffic scheduler status and configuration	Admin	+	+
show transceiver	Transceiver information	Admin	+	+
show uptime	Show system uptime	Admin	+	+
show users connected	Display information about terminal lines	Admin	+	+
show version	Display version	Admin	+	+
show virtual-network	Virtual network	Admin	+	+
show virtual-router	Virtual Router information	Admin	+	+
show vrrp	VRRP information	Admin	+	+
start-shell	Start shell	Admin	+
telnet	Open a telnet connection	Admin	+	+	+
terminal	Set terminal line parameters	Admin	+	+	+
traceroute	Trace route to destination	Admin	+	+	+
undebug	Disable debugging functions (see also 'debug')	Admin	+
virtual-container join-swarm	Virtual container settings. Join a swarm as a node	Admin	+
write	Write running configuration to memory, file or terminal	Admin	+
aaa	Authentication Authorization Accounting	Conf	+
aaa-profile	AAA server-profile configuration	Conf	+
arp	Address Resolution Protocol (ARP)	Conf	+
banner	Define a login banner	Conf	+
bgp	Border Gateway Protocol (BGP)	Conf	+
bridge	Bridge configuration	Conf	+
controller	Controller configuration	Conf	+
cvlan	Configure C-VLAN parameters	Conf	+
debug	Debugging functions (see also 'undebug')	Conf	+
debug dns client	Display DNS debugging messages	Conf	+
dhcp-profile	Select a DHCP profile to configure	Conf	+
do	To run exec commands in config mode	Conf	+
enable container	Enable containerization	Conf	+
enable password	Assign the privileged level password	Conf	+
enable vm	Enable libvirt/kvm virtualization	Conf	+
exit	End current mode and down to previous mode	Conf	+
fib	FIB information	Conf	+
flow-export-profile	Flow export profile configuration	Conf	+
help	Description of the interactive help system	Conf	+
hostname	Set system's network name	Conf	+
hw	EcoRouter platform	Conf	+
interface	Select an interface to configure	Conf	+
ip	Internet Protocol (IP)	Conf	+
IP domain-list	Define a list of default domain names used to complete unqualified host names	Conf	+
IP domain-lookup	Enable DNS host name-to-address translation	Conf	+
IP domain-name	Set the default domain name used to complete unqualified host names	Conf	+
IP host	Define static hostname-to-address mappings in DNS	Conf	+
IP name-server	Add 1-3 DNS server addresses that are used to translate hostnames to IP addresses	Conf	+
isis	Intermediate System - Intermediate System (IS-IS)	Conf	+
key	Authentication key management	Conf	+
l2vpn-vpws	Configure MPLS specific attributes	Conf	+
line	Configure a terminal line	Conf	+
mac-access-list	Add an access list entry	Conf	+
max-fib-routes	Set maximum fib routes number	Conf	+
maximum-paths	Set multipath numbers installed to FIB	Conf	+
max-static-routes	Set maximum static routes number	Conf	+
mirror-session	Select a mirror session to configure	Conf	+
mpls	Configure MPLS specific attributes	Conf	+
no	Negate a command or set its defaults	Conf	+
ntp	Configuration NTP	Conf	+
oep	Configure OVC endpoint map	Conf	+
ospf	Open Shortest Path First (OSPF)	Conf	+
platform sensor alarm	Enable sensor alarm notifications	Conf	+
policy-filter-list	Add an access list entry	Conf	+
port	Port configuration	Conf	+
role	User role management	Conf	+
route-map	Create route-map or enter route-map command mode	Conf	+
router	Enable a routing process	Conf	+
rsyslog	rsyslog options	Conf	+
security	Set security profile	Conf	+
security-profile	Security profile	Conf	+
service	Setup miscellaneous service	Conf	+
show cli	Show CLI tree of current mode	Conf	+
show list	Show command lists	Conf	+
show running-config	Current Operating configuration	Conf	+
show hosts	Display the DNS name servers and domain names	Conf	+	+	+
show running-config dns	Show the DNS settings the running configuration	Conf	+	+	+
snmp	snmp	Conf	+
snmp-server	Configure snmp server	Conf	+
traffic-class	Select a traffic class to configure	Conf	+
traffic-classifier	Select a traffic classifier to configure	Conf	+
traffic-limiter	Select a traffic limiter to configure	Conf	+
traffic-scheduler	Select a traffic scheduler to configure	Conf	+
username	Establish User Name Authentication	Conf	+
virtual-router	Virtual-router configuration	Conf	+
vlan	Configure VLAN parameters	Conf	+
vrrp	VRRP configuration	Conf	+